*Actual product and finish may vary
9860V3684 Cal-Royal Surface Vertical Rod Exit Device Grade 1 for 36" door 84" vertical rod height
Fits same hole pattern as Sargent 8800 series using 9800 escutcheon trims.
Meets THE BUY AMERICAN ACT
Handing: Specify Handing: LHR (left hand reverse) or RHR (right hand reverse) for convenience, easily field reversible.
Actual Length: 32"
Maximum Cut Down: 6"
Door Size: 30” to 36” door width
Vertical Rod Length: 84"
US3 Bright Brass, Clear Coat
US4 Satin Brass, Clear Coat
US10B Dark Bronze, Oil Rubbed
US10 Satin Bronze, Clear Coat
US32D Satin Stainless Steel
Specifications:For Doors - 1-3/4" thick standard optional 2-1/4" thick. 3-3/4" minimum stile width required for single door application. 3-1/2" minimum stile width required for double door application. Lever, thumbpiece and escutcheon trims available. 2-3/4" backset.
Chassis - Nonferrous alloy (Panic Grade), steel (Fire Grade)
Cover - Brass, Bronze or Stainless Steel.
Mounting - Furnished with wood and machine screws. Thru bolts are standard packaging on fire rated devices.
Alarm - Available. Prefix "NALRM" before part #.
End Cap - Brass, Bronze or Stainless Steel Construction.
Hand - Handed. Easily field reversible. Specify at time of order LHR, RHR for convenience.
Latch Bolt, Spring - Stainless Steel.
ANSI Standard - A156.3, Grade 1.
Rail Assembly - Heavy gauge Brass, Bronze or Stainless Steel.
Strike - See strike page.
Dogging Feature - Allen-type key furnished standard on non-fire labeled devices. Cylinder dogging available.
UL and ULC Listed - 9860 Series for panic. F9860 Series for fire exit hardware for all types of 8' x 8' double doors for up to 3 hour fire labeled installations, conforms to standards UL10C and UBC 7-2-1997 codes.
Electronic Functions - (ELR) Electrical Latch Retraction and RX & LX Signal Switch available.
Touchbar height to finished floor: 41" (1043 mm) at center
Touch bar projection - neutral: 2-1/2" (64mm)
Touch Bar Projection - depressed:1-3/4” (45mm)
Panic grade top & bottom latch case: 3-15/16" x 2-1/8" x 1-3/8" (100mm x 52mm x 42mm)
Fire Grade top latch case: 3-15/16" x 2-11/16" x 2-1/16" (100mm x 68mm x 53mm)
Fire grade Bottom latch case: 3-15/16" x 2-1/8" x 1-3/8" (100mm x 52mm x 42mm)
Top and bottom rod length for 36" x 84" doors: top rod 37-1/2" (955mm), bottom rod 84" (2134mm)
Top and bottom rod length for 48" x 96" doors: top rod 49-5/8"(1260mm), bottom rod 96" (2438mm)
Vertical rods: 1/2" (13mm) round tubingFinish - Architectural plated finishes.
Electronic Functions - (ELR) Electrical Latch Retraction and RX & LX Signal Switch available
MUST ORDER CR602RF or CR631RF POWER SUPPLY TO HONOR WARRANTY AND UL MARKING
Our electrified latch pullback exit device allows for remote keyless access control in high occupancy/high traffic conditions where exit devices are required. Common applications include conditions such as hospitals, airports, schools, churches and where they are commonly specified in applications that require automatic door openers. The device may be continuously energized allowing for a push/pull condition if desired.
Available on 9800, 7700 & 2200 Series, including rim, vertical rod, concealed vertical rod, mortise exit device, fire
and non fire-rated devices. - High-performance quality solenoids designed for demanding applications.
The PM200* interface power module (included) is programmed to meet the requirements of the specific exit device
modification. It maximizes the efficiency and life of the solenoid, allows for a much longer wire run and may be
used with 24VDC power supplies rated at 1.5A or greater - Dual coil solenoids, or PWM programming, allow for either momentary or extended time latch retraction.
No hassle 3-Year Warranty
Voltage – 24VDC
Amperage – Surge current – 12A for 200ms@24V / Holding – 250mA@24V
Coil resistance – 3.7 Ohms
To Order, Specify:
Prefix ELR before PART#
ITEM # DESCRIPTION
ELR Electrified Latch Retractor
Signal Switch RX and LX
RX (request to exit) signal switch is used to signal the use of an opening from the push side. When the push pad is depressed, the switch is activated. These devices are equipped with an internal SPDT (single pole double throw) switch that monitors the touch bar.
LX (latch bolt monitoring) signal switch monitors both egress and access of an opening. When the latch bolt is retracted, the switch is activated. These devices are equipped with an internal SPDT (single pole double throw) switch that monitors the latch bolt position.
LX and RX switches can be combined with EL (electric latch retraction) option.
RX or LX............................... Switch rated 0.5 amperes @ 24VAC/DC resistive
Low current RX or LX........... Switch rated 0.5 amperes @ 24VAC/DC resistive
For Factory Installed:
To Order, Specify:
RX.......................Request to Exit
LX........................ Latch bolt Monitoring
LXRX................... Latch bolt Monitoring/Request to Exit Combination
ITEM # DESCRIPTION
RX Request to Exit switch for field installation.
LX Latch bolt Monitoring switch for field installation.
LXRX Latch bolt Monitoring/Request to Exit Combination
Specify : 7700, 9800 or 2200 after ITEM# when ordering, for example: RX7700 to order RX switch for 7700
series exit devices
9860V3684 Cal-Royal surface vertical rod exit device 36" door 84" rod
- Brand: Cal-Royal
- Product Code: 9860V3684